AirsoftGuns s.r.o.
Universal MOS FET switch kit, PWM regulator, AirsoftGuns
Universal MOS FET switch kit is a modern electronic device that prevents tanning contacts with AEG guns, therefore increasing the rate of fire and saving the battery. This switch kit includes two powerful MOS FET transistors with extreme load current (Ip = 680A). The device is also equipped with a special circuit lossless PWM control rate of fire (motor speed) in the range of 0 to 100%. Thus you can always adjust the optimum rate of fire of your weapon irrespective of spring, the motor or battery. Now nothing stands in the way of using high-quality, low-cost, small, lightweight and powerful battery Li-Po 11.1V on the weaker springs. Without the use or bad contcylinder settings could be rate of fire so high that the risk of damaging internal components or might not be guaranteed 100% of the functions of BBs feeding, but with this regulator there is no danger. This kit is suitable for high current loads and recommend that it be installed in all guns with spring M90 - M170 in the appropriate configuration and using 11.1V Li-Pol battery. Designed for all models of weapons includes all necessary installation components and detailed installation instructions.
Universal MOS FET switch kit, PWM regulator, AirsoftGuns. Universal MOS FET switch kit is a modern electronic device that prevents arcing contacts with AEG weapons, therefore increasing the rate of fire and saving the battery.. This switch kit includes two powerful MOS FET transistors with extreme load current (Ip = 680A). The device is also equipped with a special circuit lossless rate of fire PWM control (motor speed) in the range of 0 to 100%. Thus you can always set your optimum rate of fire weapon irrespective of spring, the motor or battery. Now nothing stands in the way of using high-quality, low-cost, small, lightweight and powerful battery Li-Po 11.1V on the weaker springs. Without the use or bad cylinder settings rate of fire could be so high that the risk of damaging internal components or might not be guaranteed 100% of the functions of BBs feeding, but with this regulator there is no danger. This kit is suitable for high current loads and recommend that it is installed to all guns with spring M90 - M170 in the appropriate configuration and using 11.1V Li-Pol battery. Designed for all models of weapons includes all necessary installation components and detailed installation instructions.
PWM (pulse width modulation) controllers are used for speed control motors. This controller uses the current pulse width changes to the motor, thus differs from the ordinary continuous control current, where is not only the reduction but the current and voltage. When pulsed control current and voltage rebarrels the same but changing the active period, when current flows through the motor. Such regulated motor has more power at lower speeds, but especially this kind of regulation virtually lossless, because transistor goes into its fully open position very quickly. When opened it has a very low resistance between CE and so have losses which arise.
Package Contents:
- MOS FET switch PWM controller rate of fire with silicon wiring 1 pc
- Shrink tubing Small 2 pcs
- Shrink tubing large 2 pieces
- Shrink tubing extra -Great 1 piece
- Fast-On Connector Large 2-pack (fuse)
- Fast-On Connector 2 small pieces of (motor)
- Large blade fuse (Automotive) 32V/30A 1 piece
Recommended airsoft accessories, parameters, review and other useful information about the product Universal MOS FET switch kit, PWM regulator, AirsoftGuns can be found in the bookmarks.
PWM (pulse width modulation) controllers are used for speed control motors. This controller uses the current pulse width changes to the motor, thus differs from the ordinary continuous control current, where is not only the reduction but the current and voltage. When pulsed control current and voltage rebarrels the same but changing the active period, when current flows through the motor. Such regulated motor has more power at lower speeds, but especially this kind of regulation virtually lossless, because transistor goes into its fully open position very quickly. When opened it has a very low resistance between CE and so have losses which arise.
Package Contents:
- MOS FET switch PWM controller rate of fire with silicon wiring 1 pc
- Shrink tubing Small 2 pcs
- Shrink tubing large 2 pieces
- Shrink tubing extra -Great 1 piece
- Fast-On Connector Large 2-pack (fuse)
- Fast-On Connector 2 small pieces of (motor)
- Large blade fuse (Automotive) 32V/30A 1 piece
Recommended airsoft accessories, parameters, review and other useful information about the product Universal MOS FET switch kit, PWM regulator, AirsoftGuns can be found in the bookmarks.
